| GMDSS Test equipment |
 AIS Tester is a test device operating on AIS1 (ch87B),
AIS2(ch88B) and DSC(ch70) frequencies. The tester is designed under
corresponding standards and recommendations as a tool of operation and
installation tests of AIS unit (Automatic Identification System). The
tests’ volume comply with “Guidelines on annual testing of the AIS unit
MSC.1/Circ.1252”. |
|
Read more...
|
|
 The BEACON Tester is designed to decode and display the encoded message
from a 406 MHz Cospas-Sarsat Emergency Position Indicating Radio
Transmitter. The tester can be connected directly to the EPIRB or
monitored "over the air" using the supplied whip antenna. The tester
will decode any 406 MHz aviation protocol for EPIRB's.
A
complete measurement solution. Measures all Cospas-Sarsat frequency
channels and decodes all Cospas-Sarsat protocols. Measures 406 MHz
parameters, 121.5 MHz parameters modulation, and the in-band 406 MHz
frequency spectrum. The beacon industry is demanding higher quality
from 406 beacons and is implementing more thorough periodic testing.
EPIRB Testers that only decode the 406 message are not suitable to meet
the increasing demands from the industry to ensure the beacons are
indeed operating properly. The EPIRB Tester provides thorough beacon
measurement capabilities. |
|
Read more...
|
|
|
MF/HF/VHF GMDSS Tester MRTS-7 |
 | MF/HF/VHF DSC Marine Radio Test System (MRTS-7) is designed to check the MF/HF/VHF stations with DSC by means of SENDING/RECEIVING of DSC messages on all allowed frequencies. Besides of that Test system can be used as frequency meter and HF oscillator. |
|
|
Read more...
|
|
| The SART Tester is designed for check of any SART in accordance with the requirements of SOLAS - 74/88, and the Russian Marine Register rules M.628-2.
The SART Tester allows to:
- measure the carrier frecuency of response in range of 9140...9560 MHz;
- measure the duration of response in range of 50...150 microseconds;
- indicate the power level in range of 300...950 mW;
- calculate the quantity of sweep frecuency points in the response;
- control the power supply voltage with displaying on LCD;
- print the full protocol of the device test |
|
|
Read more...
|
|
 | According to requirements of Maritime Administrations, there is a necessity for next inspections of EPIRBs after receiving of type approval. The problem is a complexity of the basic beacon signal parameters, which could not be measured with the simplified handheld testers. The most complicated for measuring and the most important for reliable communication to satellite and accurate position calculation are the frequency stability and phase modulation parameters. As a rule they require specially designed equipment in addition to standard measurement instruments (spectrum analyzer, frequency counter, etc.) which are not usually available on a ship board.
Beacon tester BT611 allows to perform not only control tests, but comparing evaluation of different EPIRBs parameters, too.
|
|
|
Read more...
|
|
| Discounted!! This tester is out of production.
GMDSS VHF Tester allows to check all necessary parameters of VHF two-way phone equipment, GMDSS VHF equipment with DSC, and MF/HF equipment with coast servicing in accordance with rules of Russian Maritime Register of Shipping.
The VHF Tester is small and handheld.
With the help of GMDSS VHF Tester you can provide the full check of the VHF radios, MF/HF radios on comply with specification.
Tester has sound alarm of DSC transmitting/receiving. Also it provides the full self-testing with indication on LCD.
Tester can be connected to PC. |
|
|
Read more...
|
|
|
|
